The Power On Self Test
When the system is powered on, the BIOS will perform diagnostics and initialize system
components, including the video system.
(This is self-evident when the screen first flicks before the Video Card header is
displayed).
This is commonly referred as POST (Power-On Self Test).
Afterwards, the computer will proceed its final boot-up stage by calling the operating
system.
Just before that, the user may interrupt to have access to SETUP.
To allow the user to alter the CMOS settings, the BIOS provides a little program, SETUP.
Usually, setup can be entered by pressing a special key combination (DEL, ESC, CTRL-ESC,
or CRTL-ALT-ESC)
at boot time (Some BIOSes allow you to enter setup at any time by pressing CTRL-ALT-ESC).
The AMI BIOS is mostly entered by pressing the DEL key after resetting (CTRL-ALT-DEL) or
powering up the computer.
You can bypass the extended CMOS settings by holding the key down during boot-up.
This is really helpful,
especially if you bend the CMOS settings right out of shape and the computer won't boot
properly
anymore. This is also a handy tip for people who play with the older AMI BIOSes with the
XCMOS setup.
It allows changes directly to the chip registers with very little technical explanation.
A Typical BIOS POST Sequence
Most BIOS POST sequences occur along four stages:
1. Display some basic information about the video card like its brand, video BIOS version
and video memory available.
2. Display the BIOS version and copyright notice in upper middle screen. You will see a
large sequence of numbers at the bottom of the screen. This sequence is the .
3. Display memory count. You will also hear tick sounds if you have enabled it (see
Memory Test Tick Sound section).
4. Once the POST have succeeded and the BIOS is ready to call the operating system (DOS,
OS/2, NT, WIN95, etc.) you will see a basic table of the system's configurations:
? Main Processor: The type of CPU identified by the BIOS. Usually Cx386DX, Cx486DX, etc..
? Numeric Processor: Present if you have a FPU or None on the contrary. If you have a FPU
and the BIOS does not recognize it, see section Numeric Processor Test in Advanced CMOS
Setup.
? Floppy Drive A: The drive A type. See section Floppy drive A in Standard CMOS Setup to
alter this setting.
? Floppy Drive B: Idem.
? Display Type: See section Primary display in Standard CMOS Setup.
? AMI or Award BIOS Date: The revision date of your BIOS. Useful to mention when you have
compatibility problems with adaptor cards (notably fancy ones).
? Base Memory Size: The number of KB of base memory. Usually 640.
? Ext. Memory Size: The number of KB of extended memory.
In the majority of cases, the summation of base memory and extended memory does not
equal the total system memory.
For instance in a 4096 KB (4MB) system, you will have 640KB of base memory and 3072KB of
extended memory, a total of 3712KB.
The missing 384KB is reserved by the BIOS, mainly as shadow memory (see Advanced CMOS
Setup).
? Hard Disk C: Type: The master HDD number. See Hard disk C: type section in Standard
CMOS Setup.
? Hard Disk D: Type: The slave HDD number. See Hard disk D: type section in Standard CMOS
Setup.
? Serial Port(s): The hex numbers of your COM ports. 3F8 and 2F8 for COM1 and COM2.
? Parallel Port(s): The hex number of your LTP ports. 378 for LPT1.
? Other information: Right under the table, BIOS usually displays the size of cache
memory.
Common sizes are 64KB, 128KB or 256KB. See External Cache Memory section in Advanced CMOS
Setup.
AMI BIOS POST Errors
During the POST routines, which are performed each time the system is powered on, errors
may occur.
Non-fatal errors are those which, in most cases, allow the system to continue the boot up
process.
The error messages normally appear on the screen.
Fatal errors are those which will not allow the system to continue the boot-up procedure.
If a fatal error occurs, you should consult with your system manufacturer or dealer for
possible repairs.
These errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the
corresponding error.
All errors listed, with the exception of #8, are fatal errors. All errors found by the
BIOS will be forwarded to the I/O port 80h.
? 1 beep: DRAM refresh failure. The memory refresh circuitry on the motherboard is
faulty.
? 2 beeps: Parity Circuit failure. A parity error was detected in the base memory (first
64k Block) of the system.
? 3 beeps: Base 64K RAM failure. A memory failure occurred within the first 64k of
memory.
? 4 beeps: System Timer failure. Timer #1 on the system board has failed to function
properly.
? 5 beeps: Processor failure. The CPU on the system board has generated an error.
? 6 beeps: Keyboard Controller 8042-Gate A20 error. The keyboard controller (8042)
contains the gate A20 switch which allows the computer to operate in virtual mode.
This error message means that the BIOS is not able to switch the CPU into
protected mode.
? 7 beeps: Virtual Mode (processor) Exception error. The CPU on the motherboard has
generated an Interrupt Failure exception interrupt.
? 8 beeps: Display Memory R/W Test failure. The system video adapter is either missing or
Read/Write Error its memory is faulty. This is not a fatal error.
? 9 beeps: ROM-BIOS Checksum failure. The ROM checksum value does not match the value
encoded in the BIOS. This is good indication that the BIOS ROMs went bad.
? 10 beeps: CMOS Shutdown Register. The shutdown register for the CMOS memory Read/Write
Error has failed.
? 11 beeps: Cache Error / External Cache Bad. The external cache is faulty.
Other AMI BIOS POST Codes
? 2 short beeps: POST failed. This is caused by a failure of one of the hardware testing
procedures.
? 1 long & 2 short beeps: Video failure. This is caused by one of two possible hardware
faults. 1) Video BIOS ROM failure, checksum error encountered. 2) The video adapter
installed has a horizontal retrace failure.
? 1 long & 3 short beeps: Video failure. This is caused by one of three possible hardware
problems. 1) The video DAC has failed. 2) the monitor detection process has failed. 3)
The video RAM has failed.
? 1 long beep: POST successful. This indicates that all hardware tests were completed
without encountering errors.
If you have access to a POST Card reader, (Jameco, etc.) you can watch the system
perform each test by the value that's displayed.
If/when the system hangs (if there's a problem) the last value displayed will give you a
good idea where and what went wrong, or what's bad on the system board. Of course, having
a description of those codes would be helpful,
and different BIOSes have different meanings for the codes. (could someone point out FTP
sites where we could have access to a complete list of error codes for different versions
of AMI and Award BIOSes?).
BIOS Error Messages
This is a short list of most frequent on-screen BIOS error messages. Your system may show
them in a different manner. When you see any of these, you are in trouble - Doh! (Does
someone has any additions or corrections?)
? "8042 Gate - A20 Error": Gate A20 on the keyboard controller (8042) is not working.
? "Address Line Short!": Error in the address decoding circuitry.
? "Cache Memory Bad, Do Not Enable Cache!": Cache memory is defective.
? "CH-2 Timer Error": There is an error in timer 2. Several systems have two timers.
? "CMOS Battery State Low" : The battery power is getting low. It would be a good idea to
replace the battery.
? "CMOS Checksum Failure" : After CMOS RAM values are saved, a checksum value is
generated for error checking. The previous value is different from the current value.
? "CMOS System Options Not Set": The values stored in CMOS RAM are either corrupt or
nonexistent.
? "CMOS Display Type Mismatch": The video type in CMOS RAM is not the one detected by the
BIOS.
? "CMOS Memory Size Mismatch": The physical amount of memory on the motherboard is
different than the amount in CMOS RAM.
? "CMOS Time and Date Not Set": Self evident.
? "Diskette Boot Failure": The boot disk in floppy drive A: is corrupted (virus?). Is an
operating system present?
? "Display Switch Not Proper": A video switch on the motherboard must be set to either
color or monochrome.
? "DMA Error": Error in the DMA (Direct Memory Access) controller.
? "DMA #1 Error": Error in the first DMA channel.
? "DMA #2 Error": Error in the second DMA channel.
? "FDD Controller Failure": The BIOS cannot communicate with the floppy disk drive
controller.
? "HDD Controller Failure": The BIOS cannot communicate with the hard disk drive
controller.
? "INTR #1 Error": Interrupt channel 1 failed POST.
? "INTR #2 Error": Interrupt channel 2 failed POST.
? "Keyboard Error": There is a timing problem with the keyboard.
? "KB/Interface Error": There is an error in the keyboard connector.
? "Parity Error ????": Parity error in system memory at an unknown address.
? "Memory Parity Error at xxxxx": Memory failed at the xxxxx address.
? "I/O Card Parity Error at xxxxx": An expansion card failed at the xxxxx address.
? "DMA Bus Time-out": A device has used the bus signal for more than allocated time
(around 8 microseconds).
If you encounter any POST error, there is a good chance that it is an HARDWARE related
problem.
You should at least verify if adaptor cards or other removable components (simms, drams
etc...) are properly inserted before calling for help. One common attribute in human
nature is to rely on others before investigating the problem yourself.
|